How Long To Install Sliding Glass Door

Download Commodity

Download Article

Homeowners oft install sliding glass doors in lodge to let in sunlight, or to give them easy access to a patio or backyard. Information technology'southward most efficient to install a sliding glass door in an area from which a big front door—similar a set of French doors—has been removed. Y'all can install your own sliding drinking glass doors over a period of a few hours. Inquire a friend or family member to help you, since the glass doors themselves are heavy and awkward to movement.

1. i

   Cut away the interior and outside trim. Use a utility knife to cut through the caulk and paint holding the interior trim in place. Once the caulk is cut, work a pry bar into the opening. Put pressure on this to pull the interior trim away from the wall, removing it slowly and so you can deal with any caulk, paint or glue that might still be present. There may exist staples belongings the summit piece of trim to the side pieces as well. Repeat the aforementioned steps on the outside trim.^[1]

   • Don't skip cutting the caulk. If you lot pry the trim away without cutting the caulk first, you adventure dissentious the wall.
   • Set the trim bated. Yous'll need to re-attach it once the door has been installed.

2. two

   Lift the doors out of place. Grasp each section of the door firmly with both easily. Lift information technology straight up out of the running rail, and pull the door backwards out of the frame. The doors are heavy, so should be removed one at a time. Each section of the door can weigh near 100 pounds (45 kg).^[2]

   • If you're not comfortable lifting that much on your own, ask a friend to aid you with the door removal and installation process.
   • If yous find the lesser rollers are hanging up as yous lift the door, get an assistant to pry them up gently every bit y'all move the door upward and out.

   Advertisement

3. 3

   Remove nails holding the door frame in identify. Once the trim has been removed, you lot can remove any nails that are left backside. So, use a screwdriver to remove the screws which hold the frame of the sliding door to the wooden door frame. Remove screws on the left, right, top, and bottom sides of the sliding door.^[three]

   • Although you can utilize any screwdriver for this step, information technology'll be more efficient to use an electrical screwdriver.
   • If the door is older, its screws may be stripped or caked with paint or caulk, making them difficult to remove with a screwdriver. Instead, take someone hold the door to stop it from falling while you use a reciprocating saw with a bimetal bract to cut betwixt the door frame and the framing and quickly slice through whatsoever screws and nails.

   Advertisement

1. 1

   Measure the opening for your glass door. Earlier you lot shop for a door, you'll demand to know the exact size of the opening that the door needs to fill.^[iv] Use a tape measure to measure out the full width of the hole. Measure from stud to stud.^[five]

   • Measure both the width and pinnacle of the opening. Write downward these measurements so you can refer to them when shopping for a door.
   • Before you measure, make sure to remove any boards or shims that may accept been added to make the old door fit.

2. 2

   Buy a sliding glass door. Visit a home-supply shop—such as Dwelling Depot or Lowe's—and await through their selection of glass doors. Make sure to bring your tape measure with you to ostend that the door yous choose will fit well within the opening in your house. Glass door frames tin exist fabricated of various materials, including wood, vinyl, or aluminum.^[6]

   • The material and quality of the door volition determine its cost. A uncomplicated 6 anxiety (one.8 one thousand) drinking glass door volition cost around $300.
   • A pre-hung drinking glass door (which is the easiest blazon to install) will range between $1,000 and $4,000 USD. Pre-hung sliding glass doors can be installed equally a single unit of measurement. You won't demand to assemble the frame before installing information technology in your wall.

3. 3

   Make clean upward and accommodate the opening. At this point, the opening that yous pulled the erstwhile door out of volition likely be cluttered and rough. Remove whatsoever leftover nails or torn material. You may also demand to suit the opening. Use a carpenter'southward level to make sure that the top, bottom, and side frames of the opening area all level.^[7]

   • If any aren't level, you can utilize a shim to even out the door frame.
   • If the frame is slightly besides large for the sliding door you purchased, nail in 1 or more than strips of 1x3 plywood to adjust the size of the opening.

   Advert

1. one

   Apply flashing to the door frame. Flashing is a type of adhesive, waterproof tape that will protect the door frame and lower edges of the sliding glass door from water harm. Flashing volition likewise prevent water from inbound around the edges. Apply a layer of flashing along the bottom sill of the doorframe. Let the tape hang over the outer edge of the doorframe, then you lot tin bend the tape over and press information technology down on the external side.^[8]

   • Also apply a single layer of flashing about 6 inches (fifteen cm) up the doorjamb on both sides.
   • Y'all can purchase flashing at any hardware shop or home-supply store.

2. two

   Gear up the door frame in place. Take a friend help you lot elevator and comport the door frame inside the house, and push it into position in the large opening. Be sure not to install the door backwards. The side with the small-scale track for the sliding screen should face outwards.^[9]

   • Some cheap vinyl sliding door models may need to be assembled.^[x]

3. 3

   Screw the frame in identify and add insulation. Use the same screws that yous removed from the sides, height, and bottom of the old door frame. Spiral these through the material of the new door frame, and tighten until they're securely embedded in the door frame.^[11] Use of a level is essential to ensure the frame is perfectly straight on all sides as you screw it in and if you lot are working on an older home have door shims handy to correct if necessary. Otherwise, the doors may not fit properly.

   • If there are sizeable gaps above and on the sides of the door frame, stuff a sheet or two of fiberglass insulation into these spaces. This will prevent your house from losing heat effectually the frame.^[12]

4. four

   Install the sliding glass panels and handle. Offset, carefully clean all droppings from the rail to get a skilful fit. Then, have a friend help y'all elevator the first department of the sliding door. Ready the bottom in place on the track in the door frame, and then press the top portion of the door in place too.^[13] Echo with the second section of the sliding door.^[14]

   • At this point, you can also attach the metal handles that came with the sliding drinking glass door. These handles should come with screws provided, which yous'll screw into indicated holes on the front and back of the glass door.
   • Yous tin attach the lock squeeze at this point as well. This is the minor plastic chip that allows the lock on the door to hold it in place against the frame.^[15]

5. five

   Re-attach the interior and exterior trim. Now that the door is securely in place, you can nail the interior and exterior trim back in place as well. Adhere these to the aforementioned locations from which you removed them at the starting time of the process.^[16]

   • One time the trim is hung, you lot won't be able to see the sides of the door frame or the studs to which you lot screwed the door.

6. 6

   Put up the screen. As the concluding footstep in installing your glass door, put in the screen. Snap it into place on both the top and bottom running tracks. Make sure that the screen slides open and close without difficulty.^[17]

   • At this indicate, your door is installed and ready for use.

   Advertisement

Ask a Question

200 characters left

Include your electronic mail address to get a message when this question is answered.

Submit

Advertizing

Things You'll Need

• Utility knife
• Pry bar
• Screwdriver
• Hammer
• Tape measure
• Sliding drinking glass door
• Level
• Shims or plywood strips (optional)
• Nails
• Flashing tape
• Insulation (optional)

• Begin and complete the installation while the conditions is fair and warm. You'll have a large opening in a wall of your dwelling house for several hours of the 24-hour interval, then make certain that the 24-hour interval won't be common cold or rainy.^[18]

• Former sliding glass doors tin can also exist replaced with pre-hung French doors if you prefer. Sizes will tend to be a piffling different, just equally long as you select French doors that are slightly smaller than the old door, it will be adequately easy to add more material to your frame to brand information technology fit. Avoid getting doors that are too big, since it is much more difficult to endeavour to make them smaller.

Advertizement

Virtually This Article

Article Summary X

To install a glass door, start by appying waterprooof adhesive to the frame to protect it from water damage. Adjacent, lift the frame into position and attach it to the walls with screws. If you lot see gaps between the wall and the frame, fill up them in with insulation then you don't lose heat from your abode. Additionally, position the door panels in the slot at the lesser, and install the handles and lock clasp. Finally, install the screen, and the interior and exterior trim to complete the chore. For tips on how to purchase a drinking glass door, keep reading!

Did this summary aid you?

Thanks to all authors for creating a page that has been read 50,785 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Sliding-Glass-Door

Posted by: petriagge1969.blogspot.com

Share this post